THE ART OF BASIC PLUMBING FOR INSTALLING A BATHTUB

The Art of Basic Plumbing for Installing a Bathtub

The Art of Basic Plumbing for Installing a Bathtub

Blog Article

Call

Do you find yourself on the lookout for know-how about How to Install a Bathtub Yourself?


How to Install a Bathtub
Setting up a bath tub isn't precisely rocket science, however it does call for solid plumbing, carpentry, and sometimes, tiling abilities. Replacing an old tub with a brand-new one is additionally a reasonably tough job. If the old tub is easily accessible, the project can move easily; if you have to open a wall surface to get rid of the old tub and position the new tub, the task is much harder. In either instance, the job is within a residence handyman's skills, although you will require an assistant to vacate the old tub and also set in the brand-new one. Make sure you have certified yourself for the task and fit trying it. Instead of hiring a contractor to take control of a halfway-completed job, it is much better to think about utilizing one prior to you start. Opportunities are you might require a specialist plumber to make tube connections.
This post will certainly aid you mount a brand-new bathtub in your shower room if you have currently purchased a brand-new bathtub and also do not need to change the setup of your previous supply of water pipes.
Your tools and product checklist ought to comprise the following:
  • New Bath tub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Chisel

  • Measuring tape

  • Pipeline Caps


  • Planning for the Setup


    To start with, the supporting frame provided with the bathroom ought to be fitted (if required) according to the producer's guidelines. Next off, fit the taps or mixer to the tub. When fitting the faucet block, it is necessary to see to it that if the tap comes with a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bath, it is also practical to fit a supporting plate under the faucets system to stop strain on the bathtub.
    Fit the versatile tap connectors to the bottom of both taps using 2 nuts and also olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet via the hole in the bath. Use the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next off, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. See to it you make use of all of the provided washing machines.
    Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom should now prepare to be fitted in its final setting.

    Removing Old Taps


    If you need to change old faucets with brand-new ones as a part of your installation, after that the first thing you must do is disconnect the supply of water. After doing so, turn on the faucets to drain pipes any water staying in the system. The procedure of eliminating the existing faucets can be quite troublesome as a result of the limited accessibility that is usually the instance.
    Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipes to the taps. Have a cloth all set for the continuing to be water that will certainly come from the pipes. When the supply pipelines have actually been eliminated, use the same device to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the single taps from transforming during this process. As soon as the taps have been removed, the holes in the bath/basin will need to be cleansed of any kind of old sealing compound.
    Prior to carrying on to fit the new taps, compare the pipe links on the old taps to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is required for the new faucets to fit.

    Setting up the Bath tub


    Utilizing the two wooden boards under its feet, place the bath tub in the needed placement. The wooden boards are useful in equally spreading the weight of the tub over the location of the boards as opposed to focusing all the weight onto four small points.
    The following objective is to make certain that the tub is leveled all round. This can be attained by inspecting the spirit level and also changing the feet on the bathtub until the spirit level reviews level.
    To set up taps, fit the bottom of the furthest adaptable tap port to the ideal supply pipeline by making a compression join; then do the same for the other faucet.
    Activate the water supply as well as examine all joints as well as new pipework for leaks and tighten them if essential. Load the tub and likewise inspect the overflow electrical outlet and also the normal outlet for leaks.
    Lastly, repair the bathroom paneling as explained in the manufacturer's user's manual. Tiling as well as securing around the bath tub must wait up until the bath tub has been made use of a minimum of when as this will certainly settle it into its final position.

    Fitting New Touches


    If the tails of the new taps are plastic, after that you will certainly require a plastic port to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end gives a connection to the existent supply pipes.
    If you require to fit a monobloc, then you will certainly require decreasing couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipe.
    Next, place the faucet in the placing hole in the bath/basin ensuring that the washers are in location between the tap and also the sink. Secure the tap in place with the producer supplied backnut. When the faucet is firmly in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with normal faucet connectors. The former kind ought to be linked to the faucet finishes first, tightening only by hand. The supply pipes can later be linked to the other end. Tighten up both ends with a spanner after both ends have actually been linked.

    Tiling Around the Bathtub


    In the location where the bathroom meets the tile, it is required to seal the joins with a silicone rubber caulking. This is important as the installation can relocate sufficient to fracture an inflexible seal, creating the water to pass through the wall surface in between the bathroom and the tiling, resulting in complications with moisture and feasible leaks to the ceiling below.
    You can pick from a variety of coloured sealers to assimilate your components as well as installations. They are offered in tubes as well as cartridges, as well as are capable of securing gaps up to a width of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with spins of drenched paper or soft rope. Remember to always fill the bathtub with water prior to securing, to allow for the movement experienced when the tub is in use. The sealant can split rather very early if you do not consider this motion prior to sealing.
    Additionally, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also quickly offered on the marketplace. It is recommended to fit the ceramic tiles using waterproof or waterproof adhesive and grout.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    How to Install a Bathtub

    We had been made aware of that report about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround from a friend on a different web address. Loved our content? Please share it. Let somebody else find it. Kudos for your time. Kindly check up our blog back soon.


    Click Here To Find Out More

    Report this page